Cabinetmaker (CAB)

First Period Package (39 Modules) Comments

Date: 2/18/2020 3:22:04 PM
Module: 360101a
Version: 21
Page: 26
Comment: Add Oscillating Multi-tool
Status: Approved for Review

Date: 2/18/2020 3:14:55 PM
Module: 360101cA
Version: 21
Page: 16
Comment: Objective Two - Please add "Classes of Fires" from 020201c (pg 39-41).
Status: Approved for Review

Date: 2/18/2020 3:15:08 PM
Module: 360101d
Version: 21
Page: 26
Comment: MSDS should read "SDS" as per new WHMIS regulations. (Please use search function to find all.)
Status: Approved for Review

Date: 2/18/2020 3:15:17 PM
Module: 360101e
Version: 21
Page: 6
Comment: Replace MSDS with SDS in Figure 4 and in the 2nd paragraph.
Status: Approved for Review

Date: 2/18/2020 3:15:48 PM
Module: 360102c
Version: 21
Page: 20
Comment: Figure 22 - replace with cross banding of plywood illustration.
Status: Approved for Review

Date: 2/18/2020 3:15:55 PM
Module: 360102c
Version: 21
Page: 12
Comment: Table 2 - reverse High density and Low density.
Status: Approved for Review

Date: 2/18/2020 3:16:04 PM
Module: 360102d
Version: 21
Page: 29
Comment: Recommend increased emphasis on dangers associated with the use of urea resin.
Status: Approved for Review

Date: 2/18/2020 3:17:23 PM
Module: 360102e
Version: 21
Page: 16
Comment: Figure 13 - lighten image
Status: Approved for Review

Date: 2/18/2020 3:17:32 PM
Module: 360102e
Version: 21
Page: 21
Comment: Figure 24 - Poor illustration.
Status: Approved for Review

Date: 2/18/2020 3:18:26 PM
Module: 360102e
Version: 21
Page: 22
Comment: Figure 25 & Figure 27 - too small. Please enlarge.
Status: Approved for Review

Date: 2/18/2020 3:18:33 PM
Module: 360102e
Version: 21
Page: 23
Comment: Figure 28 - too small. Please enlarge. Figure 29 - wrong illustration. Please replace.
Status: Approved for Review

Date: 2/18/2020 3:18:40 PM
Module: 360102e
Version: 21
Page: 24
Comment: Figure 31 - too small. Please enlarge.
Status: Approved for Review

Date: 2/18/2020 3:18:48 PM
Module: 360102g
Version:
Page: 26
Comment: Style should Stile
Status: Approved for Review

Date: 2/18/2020 3:18:55 PM
Module: 360102g
Version: 21
Page: 37
Comment: 6th bullet - whole should be hole
Status: Approved for Review

Date: 2/18/2020 3:19:02 PM
Module: 360103a
Version: 21
Page: 24
Comment: Figure 28 - replace with a laser level illustration. Figure 30 - replace with a laser level illustration.
Status: Approved for Review

Date: 2/18/2020 3:21:46 PM
Module: 360103a
Version: 21
Page: 23
Comment: Line Level - delete text and Figure 27. Cabinetmaker do not use string levels. Figure 30 - delete line level.
Status: Approved for Review

Date: 2/18/2020 3:21:53 PM
Module: 360103a
Version: 21
Page: 29
Comment: Figure 37 - remove micrometer (right side of picture).
Status: Approved for Review

Date: 10/18/2020 10:29:45 AM
Module: 360103a
Version: 2.4
Page: 9
Comment: Laser measuring devices are quite common in the industry. they can be as accurate as 0.5 of a mm over a long distance. I feel that this could be added to the ILM as a measuring device.
Status: Update in Progress

Date: 10/18/2020 10:30:04 AM
Module: 360103a
Version: 2.4
Page: 24
Comment: I feel there should be a new tool introduced in this area. The self leveling laser level. They are invaluable to the installer of millwork, tile, electrical and many other trades. For instance the Bosch GLL3-80P has a 360 degree line that works on 2 planes, doing level, plumb lines, and also plumb crosshairs.
Status: Update in Progress

Date: 2/18/2020 3:22:11 PM
Module: 360103b
Version: 21
Page: 34
Comment: Wheel grinders - these are a fire hazard in the shop. Should they be removed and replaced with wet wheel grinders (Tormek).
Status: Approved for Review

Date: 2/18/2020 3:22:20 PM
Module: 360103b
Version: 21
Page: 31
Comment: The practice of truing up wet stones using a cinder block is questionable. Perhaps using a granite stone is more applicable.
Status: Approved for Review

Date: 2/18/2020 3:22:35 PM
Module: 360103b
Version: 21
Page: 28
Comment: Figure 40 - delete illustration.
Status: Approved for Review

Date: 2/18/2020 3:22:41 PM
Module: 360103b
Version: 21
Page: 30
Comment: Figure 43 - delete
Status: Approved for Review

Date: 2/18/2020 3:22:48 PM
Module: 360103b
Version: 21
Page: 35
Comment: Figure 50 & 51 - should have same range as other ILMs...25-30°
Status: Approved for Review

Date: 10/18/2020 10:30:44 AM
Module: 360103b
Version: 2.2000000000000002
Page: 39
Comment: Bench grinders have been abolished from the Cabinetmaking labs. They are a fire hazard and have been replaced with wet grinding wheels such as the Tormek T-8 I feel that this should be added tot he ILM.
Status: Update in Progress

Date: 2/18/2020 3:22:27 PM
Module: 360103c
Version: 21
Page: 15, 16
Comment: Figure 20 & 21 - update illustration with cabinet scraper.
Status: Approved for Review

Date: 2/18/2020 3:22:55 PM
Module: 360103d
Version: 21
Page: 11, 12
Comment: Delete section on "Brad Pushers" (text and figures). This is obsolete.
Status: Approved for Review

Date: 2/18/2020 3:23:02 PM
Module: 360103d
Version: 21
Page: 33
Comment: Figure 53 - illustration is an unsafe practice. Please delete.
Status: Approved for Review

Date: 2/18/2020 3:23:10 PM
Module: 360103d
Version: 21
Page: 18
Comment: Figure 28 - update illustration.
Status: Approved for Review

Date: 2/18/2020 3:23:17 PM
Module: 360103d
Version: 21
Page: 28
Comment: Figure 43 - This is a carpenter tool not a cabinetmaker tool.
Status: Approved for Review

Date: 2/18/2020 3:23:36 PM
Module: 360103d
Version: 21
Page: 7
Comment: Figure 8 - Cross cut and rip images need to be reversed.
Status: Approved for Review

Date: 2/18/2020 3:23:44 PM
Module: 360103d
Version: 21
Page: 16, 17
Comment: Figure 25 - delete Figure 28 - delete section on Flooring Saw
Status: Approved for Review

Date: 2/18/2020 3:23:26 PM
Module: 360103e
Version: 21
Page: 2
Comment: Figure 1 - delete bit and brace. Not used in industry. Discussion on Objective One.
Status: Approved for Review

Date: 2/18/2020 3:23:51 PM
Module: 360103fA
Version: 21
Page: 2
Comment: Should include information on Impact Drivers.
Status: Approved for Review

Date: 2/18/2020 3:23:59 PM
Module: 360103fA
Version: 21
Page: 9
Comment: Figure 10 - update illustration and text.
Status: Approved for Review

Date: 2/18/2020 3:24:07 PM
Module: 360103fA
Version: 21
Page: 26
Comment: Figure 35 - update image.
Status: Approved for Review

Date: 10/18/2020 10:32:15 AM
Module: 360103fA
Version: 3.2
Page: 25
Comment: A more practical method of starter holes when using a jigsaw is to drill holes in opposing corners rather than adjacent ones, This eliminates having to make curve cuts,
Status: Update in Progress

Date: 10/18/2020 10:32:29 AM
Module: 360103fA
Version: 3.2
Page: 2
Comment: There is mention of cordless drills, however, in the last 15 or more years the impact driver is more commonly used in the industry. There is no indication of this tool in the module.
Status: Update in Progress

Date: 2/19/2020 3:17:51 PM
Module: 360103fB
Version: 21
Page: 26
Comment: Add "Festool Domino" tooling...end of page.
Status: Approved for Review

Date: 2/19/2020 3:17:59 PM
Module: 360103fB
Version: 21
Page: 6
Comment: Figure 8 is inaccurate. Replace with new image.
Status: Approved for Review

Date: 2/19/2020 3:19:12 PM
Module: 360103fB
Version: 21
Page: 11, 12, 13
Comment: Remove from Bits and Cutters on page 11 up to Cutter Rotation on page 13.
Status: Approved for Review

Date: 2/19/2020 3:18:05 PM
Module: 360103g
Version: 21
Page: 13
Comment: Add 23 gauge headless pin nailer behind "Finishing Nailers".
Status: Approved for Review

Date: 2/19/2020 3:18:13 PM
Module: 360103g
Version: 21
Page: 25
Comment: Add to Notebox: "Not all pneumatic tools require oil. Check manufacturer's recommendations."
Status: Approved for Review

Date: 2/19/2020 3:18:20 PM
Module: 360103h
Version: 21
Page: 32
Comment: Recommend to remove section on Radial Arm saws.
Status: Approved for Review

Date: 2/19/2020 3:18:31 PM
Module: 360103h
Version: 21
Page: 42
Comment: CNC Band Saws are used in metal fabrication. Remove section.
Status: Approved for Review

Date: 2/19/2020 3:18:38 PM
Module: 360103h
Version: 21
Page: 41
Comment: Figure 63 is inaccurate. Must be updated.
Status: Approved for Review

Date: 2/19/2020 3:18:45 PM
Module: 360103h
Version: 21
Page: 51
Comment: Radial Arm Safety - recommend removing.
Status: Approved for Review

Date: 2/19/2020 3:18:51 PM
Module: 360103i
Version: 21
Page: 6
Comment: Recommend removing "Steel Teeth" - text and Figure 6
Status: Approved for Review

Date: 2/19/2020 3:18:58 PM
Module: 360103i
Version: 21
Page: 17
Comment: Recommend removing "High Speed Steel Saw Blade Reconditioning", "Filing Rip Teeth" and "Filing Crosscut Teeth".
Status: Approved for Review

Date: 2/19/2020 3:19:05 PM
Module: 360103i
Version: 21
Page: 35
Comment: Figure 51 - caption should read: "Spoil board cutter."
Status: Approved for Review

Date: 10/18/2020 10:33:08 AM
Module: 360103i
Version: 3.2
Page: 24
Comment: There is a conflict in the distance of driving fasteners from the edge of concrete. In the general recommendations above the picture it states 75mm, and the actual picture below shows 50mm.
Status: Update in Progress

Date: 2/19/2020 3:19:23 PM
Module: 360103j
Version: 21
Page: 33, 34
Comment: Section on Auger Bits - pages 33 and 34
Status: Approved for Review

Date: 2/19/2020 3:19:29 PM
Module: 360103k
Version: 21
Page: 3
Comment: Figure 2: Replace picture with chop saw.
Status: Approved for Review

Date: 2/19/2020 3:19:35 PM
Module: 360103l
Version: 21
Page: 24
Comment: Change reference distance on concrete edge to 50mm
Status: Approved for Review

Date: 2/19/2020 3:19:42 PM
Module: 360103l
Version: 21
Page: 28
Comment: Diagram and description both incorrect for distance from edge of steel. (supposed to be 12mm)
Status: Approved for Review

Date: 2/19/2020 3:19:50 PM
Module: 360103l
Version: 21
Page: 4
Comment: Discrepancy in the description does not align with the chart on page 10 (Low velocity vs normal velocity, 90m/s)
Status: Approved for Review

Date: 2/19/2020 3:19:57 PM
Module: 360103l
Version: 21
Page: 5
Comment: Remove nickle charges in high velocity tools, they are no longer available.
Status: Approved for Review

Date: 2/19/2020 3:20:03 PM
Module: 360104b
Version: 21
Page: 8
Comment: Correction needed for figure 11, example 4. front view is incorrect. (should resemble a triangle)
Status: Approved for Review

Date: 2/21/2020 2:56:07 PM
Module: 360104c
Version: 21
Page:
Comment: a. Page 34 fig.32 b. Change extension line to go past dimension line 2mm not 3mm
Status: Approved for Review

Date: 2/21/2020 2:56:15 PM
Module: 360104c
Version: 21
Page: 36
Comment: a. Page 36 fig.34 b. Change offset to 1.5mm to eliminate need to adjust Ames lettering guide
Status: Approved for Review

Date: 3/8/2020 7:31:33 AM
Module: 360104d
Version: 21
Page: 11
Comment: Fig 9 Grain direction on side gable should be horizontal to match AIT requirements. Recommend new image.
Status: Approved for Review

Date: 3/8/2020 7:31:45 AM
Module: 360104d
Version: 21
Page: 11
Comment: Fig 10 Extension lines should not share two views, recommend new image similar to fig 3, construction lines can be shared but not dimension lines.
Status: Approved for Review

Date: 2/21/2020 2:56:22 PM
Module: 360104fB
Version: 21
Page: 12
Comment: Figure 4 - update image to match Castilian drawing index page.
Status: Approved for Review

Date: 2/21/2020 2:56:31 PM
Module: 360104fB
Version: 21
Page: 12
Comment: 2nd paragraph - should read: Example 5 not 1.
Status: Approved for Review

Date: 2/21/2020 2:56:37 PM
Module: 360104fB
Version: 21
Page: 22
Comment: Figure 20 - update image to match Castilian index page.
Status: Approved for Review

Date: 2/21/2020 2:56:44 PM
Module: 360104fB
Version: 21
Page: 24
Comment: Figure 22, 29, 33, 37 - replace image to match Castilian index page.
Status: Approved for Review

Date: 2/21/2020 2:56:51 PM
Module: 360105aA
Version: 21
Page: 12
Comment: Figure 16, 17, 18, 19, 20, 21 - Calculator should be Casio FX260. Please replace images.
Status: Approved for Review

Date: 2/21/2020 2:56:59 PM
Module: 360105aB
Version: 21
Page: 21
Comment: Last 4 equations - change 1st equal sign to multiplication sign
Status: Approved for Review

Date: 2/21/2020 2:57:06 PM
Module: 360105bB
Version: 21
Page: 2
Comment: Under Board Feet: change formula to T" x W" x L" divided by 144
Status: Approved for Review

Date: 2/21/2020 2:57:13 PM
Module: 360105bB
Version: 21
Page: 29
Comment: Answer #8 - 4th line - change 1 to .1 5th line change 0.576715 to 0.0576715
Status: Approved for Review

Date: 2/21/2020 2:57:19 PM
Module: 360105c
Version: 21
Page: 7
Comment: 1st bullet to read: An increase in the diameter...
Status: Approved for Review


Archived Comments

There are no archived comments to view for this package.