Cabinetmaker (CAB)

Second Period Package (32 Modules) Comments

Date: 3/8/2020 7:41:25 AM
Module: 360201a
Version: 21
Page: 15
Comment: Spelling error: Under containment and delivery, should read simple instead of simply.
Status: Approved for Review

Date: 3/8/2020 7:41:35 AM
Module: 360201a
Version: 21
Page: 16
Comment: Under gravity feed: Last sentence should read "hoists" instead of "hosts"
Status: Approved for Review

Date: 5/12/2021 3:24:58 PM
Module: 360201a
Version: 21
Page: 5
Comment: Add note that formaldehyde is a carcinogenic.
Status: Update in Progress

Date: 5/12/2021 3:27:23 PM
Module: 360201a
Version: 21
Page: 6
Comment: Extension lines 2mm past dimension lines, not 3. Fig. 4 same.
Status: Declined

Date: 5/13/2021 10:53:31 AM
Module: 360201bA
Version: 21
Page: 41
Comment: Add "aventos" style door hinge/flap in illustrations.
Status: Declined

Date: 5/12/2021 3:31:01 PM
Module: 360201bB
Version: 21
Page: 6
Comment: Figure 7: Update to actual image.
Status: Update in Progress

Date: 5/12/2021 3:31:21 PM
Module: 360201bB
Version: 21
Page: 22
Comment: Delete figure 35 Not a catch.
Status: Declined

Date: 5/12/2021 3:32:08 PM
Module: 360201bB
Version: 21
Page: 11
Comment: Figure 15: Questionable image. Gloves on table saw.
Status: Update in Progress

Date: 5/12/2021 3:33:37 PM
Module: 360201bB
Version: 21
Page: 44
Comment: Provide updated illustrations of ball bearing under-mount slides, and metal sided drawers. (metabox)
Status: Update in Progress

Date: 5/13/2021 5:23:51 PM
Module: 360201bB
Version: 21
Page: 10
Comment: Figure 14 is a dangerous practice. Remove.
Status: Update in Progress

Date: 5/12/2021 3:33:57 PM
Module: 360201bC
Version: 21
Page: 17
Comment: Update illustrations: Remove figure 31 CPU holders.
Status: Declined

Date: 5/12/2021 3:38:09 PM
Module: 360201bC
Version: 21
Page: 22
Comment: Figure 39: Update photo, plastic isn't available anymore.
Status: Update in Progress

Date: 5/3/2021 4:04:50 PM
Module: 360201cB
Version: 21
Page: 22
Comment: Page 22: Spelling error. 4th paragraph, 2nd sentence. "whipped" to "wiped"
Status: Implemented

Date: 5/3/2021 4:09:34 PM
Module: 360201d
Version: 21
Page: 7
Comment: Figure 9: Third item is an architrave, not a crown moulding.
Status: Implemented

Date: 3/8/2020 7:30:58 AM
Module: 360202a
Version: 21
Page: 12
Comment: Steps to machine mortise should be to machine each end, then middle.
Status: Approved for Review

Date: 5/12/2021 3:38:24 PM
Module: 360202a
Version: 21
Page: 9
Comment: Figure 10: Incorrect illustration. Should read bushing to hold hollow chisel.
Status: Update in Progress

Date: 5/12/2021 3:40:14 PM
Module: 360202a
Version: 21
Page: 41, 42
Comment: Old figures: 47, & 48. remove square cutter-head images
Status: Update in Progress

Date: 3/8/2020 7:32:19 AM
Module: 360202bA
Version: 21
Page: 25
Comment: Fence: third sentence replace stout wooden jaws with wooden off set fences.
Status: Approved for Review

Date: 3/8/2020 7:32:29 AM
Module: 360202bA
Version: 21
Page: 27
Comment: Fence adjustments: second sentence replace wooden jaws with wooden offset fences replace fence jaws with wooden offset fences.
Status: Approved for Review

Date: 5/12/2021 3:41:35 PM
Module: 360202bA
Version: 21
Page: 31
Comment: Fig 49 The illustration should be a starter pin on a shaper table not a router table. recommend new image.
Status: Declined

Date: 5/12/2021 3:41:54 PM
Module: 360202bA
Version: 21
Page: 27
Comment: fig 42 second illustration should read "off set fence slides side to side" the note for fig 42 'heavy wooden offset fence"
Status: Update in Progress

Date: 5/12/2021 3:49:50 PM
Module: 360202c
Version: 21
Page: 1
Comment: Introduction: second third and forth sentences need to be removed,these machines are not covered in this ILM.
Status: Update in Progress

Date: 5/12/2021 3:50:39 PM
Module: 360202c
Version: 21
Page: 2
Comment: Reduce the amount of content covered on the Stroke sander.
Status: Declined

Date: 5/12/2021 3:51:23 PM
Module: 360202d
Version: 21
Page: 8
Comment: Fig 10 illustration does not match the drive system content.
Status: Update in Progress

Date: 5/12/2021 3:51:34 PM
Module: 360202d
Version: 21
Page: 22
Comment: second sentence should read " pilot holes that are the size of the shaft or root diameter of the screw" Fig 30 illustration needs to reflect root diameter of screw.
Status: Update in Progress

Date: 5/13/2021 10:57:01 AM
Module: 360202d
Version: 21
Page: 29
Comment: second sentence spelling of calliper should be caliper.
Status: Update in Progress

Date: 5/12/2021 3:52:21 PM
Module: 360202e
Version: 21
Page: 8
Comment: Exposed surfaces; paragraph 2 second and third sentences do not apply to the fig 9 image.
Status: Update in Progress

Date: 5/12/2021 3:52:43 PM
Module: 360202e
Version: 21
Page: 35
Comment: Fig 34 should read types of "sheet goods" or "panel products" instead of types of plywood.
Status: Update in Progress

Date: 5/12/2021 3:52:55 PM
Module: 360202e
Version: 21
Page: 38
Comment: Fig 38 should read " LPLs are similar to high- pressure laminates.... also referred to as melamine"
Status: Update in Progress

Date: 5/12/2021 3:53:06 PM
Module: 360202e
Version: 21
Page: 39
Comment: Figure 40: Update mage of honeycomb.
Status: Update in Progress

Date: 5/12/2021 3:53:16 PM
Module: 360202e
Version: 21
Page: 45
Comment: Delete Radial arm saw. It is not a conventional machine. Perhaps add "chop saw"
Status: Update in Progress

Date: 5/12/2021 3:53:41 PM
Module: 360202e
Version: 21
Page: 49
Comment: Third paragraph, second sentence: Should read "could these descriptions be combined to say what they do and that they come in 2 forms. Circular, or bandsaw, (which is used in large mills)
Status: Declined

Date: 5/13/2021 10:57:13 AM
Module: 360202e
Version: 21
Page: 6
Comment: Fig 7 note: spelling mistake staking should read "sticking"
Status: Update in Progress

Date: 5/13/2021 11:04:26 AM
Module: 360202e
Version: 21
Page: 42
Comment: Second paragraph: Description of child's crib is not feasable, omit sentence.
Status: Update in Progress

Date: 5/12/2021 3:58:56 PM
Module: 360202fA
Version: 21
Page: 5
Comment: Figure 3: Change illustration, second cabinet isn't a common casework assembly practice.
Status: Declined

Date: 5/12/2021 3:59:22 PM
Module: 360202fA
Version: 21
Page: 13
Comment: Top of page: All units should be metric. New tolerances should be 0.5mm general tolerance and 0.1mm fine tolerance on a table saw. 0.1mm accuracy on a CNC saw.
Status: Update in Progress

Date: 5/12/2021 4:00:15 PM
Module: 360202fA
Version: 21
Page: 40
Comment: Figure 49 is confusing. A clearer illustration is required.
Status: Update in Progress

Date: 5/12/2021 4:00:24 PM
Module: 360202fA
Version: 21
Page: 42
Comment: Figure 52: an illustration is needed for baltic birch drawer construction. Omit the one that's there.
Status: Update in Progress

Date: 5/12/2021 4:00:35 PM
Module: 360202fA
Version: 21
Page: 48
Comment: Last paragraph need to be broken up into 3 or 4 smaller paragraphs.
Status: Update in Progress

Date: 5/13/2021 11:04:50 AM
Module: 360202fA
Version: 21
Page: 10
Comment: First paragraph should read: A cutting list is used to generate a materials list that will also be used for the bill of materials.
Status: Update in Progress

Date: 5/13/2021 11:05:12 AM
Module: 360202fA
Version: 21
Page: 12
Comment: Third last sentence: should read 0.25mm, not 0.025mm
Status: Update in Progress

Date: 5/13/2021 11:07:31 AM
Module: 360202fA
Version: 21
Page: 17
Comment: Bottom of page: Under cabinet styles last sentence should read "Shared gable construction" not bale.
Status: Update in Progress

Date: 5/13/2021 11:09:05 AM
Module: 360202fA
Version: 21
Page: 28
Comment: Change paragraph, incorrect statement: You are able to stack multiple sheets and produce a chip free edge on all the parts. Scoring blade will prevent chips on the bottom sheet only.
Status: Update in Progress

Date: 5/13/2021 11:09:38 AM
Module: 360202fA
Version: 21
Page: 38
Comment: Second paragraph: Should read "Custom" (Not common)
Status: Update in Progress

Date: 5/13/2021 12:27:42 PM
Module: 360202fA
Version: 21
Page: 22
Comment: Figure 22: needs an additional step. apply top and bottom overlays, then trim.
Status: Update in Progress

Date: 5/12/2021 4:00:45 PM
Module: 360202gA
Version: 21
Page: 20
Comment: fig 29 illustration is poor, refer to older version 2.2
Status: Update in Progress

Date: 5/12/2021 4:00:56 PM
Module: 360202gA
Version: 21
Page: 31
Comment: fig 43 is incorrect, please revert back to ILM version 2.2.
Status: Update in Progress

Date: 5/13/2021 11:11:59 AM
Module: 360202gA
Version: 21
Page: 21
Comment: Fig 30 Should read "Jamb at Lite" not Jamb at life.
Status: Update in Progress

Date: 5/13/2021 11:12:10 AM
Module: 360202gA
Version: 21
Page: 23
Comment: Sidelights and transoms should read "sidelites" also on fig 33.
Status: Update in Progress

Date: 5/3/2021 4:11:40 PM
Module: 360202h
Version: 21
Page: 1
Comment: Second sentence: Remove first "Driven" in sentence.
Status: Implemented

Date: 5/3/2021 4:11:52 PM
Module: 360202h
Version: 21
Page: 24
Comment: Referring to stacking (3rd sentence) Stacking does not chip sheets. Scoring blade should only cut 1/2mm deep
Status: Implemented

Date: 5/3/2021 4:12:04 PM
Module: 360202h
Version: 21
Page: 37
Comment: Self test: Question 4. Correct answer is "b" not "a" Change answer.
Status: Implemented

Date: 5/12/2021 4:09:14 PM
Module: 360202h
Version: 21
Page: 24
Comment: Keep first 2 sentences referring to stacking. the rest is inaccurate.
Status: Update in Progress

Date: 10/15/2021 10:52:29 AM
Module: 360202h
Version: 21
Page: 27
Comment: Figure 31: A better illustration of a beam machine is required. This one looks like a gantry.
Status: Declined

Date: 3/8/2020 7:24:40 AM
Module: 360203a
Version: 21
Page: 21
Comment: A description of a pre-filter is needed.
Status: Approved for Review

Date: 5/12/2021 4:12:52 PM
Module: 360203a
Version: 21
Page: 23
Comment: Figure 22: Picture has new and used are reversed.
Status: Update in Progress

Date: 5/13/2021 11:48:20 AM
Module: 360203a
Version: 21
Page: 5
Comment: Fugure 3: MSDS is now referred to as SDS
Status: Update in Progress

Date: 5/13/2021 11:48:51 AM
Module: 360203a
Version: 21
Page: 8, 10, 13, 14
Comment: Table 1: MSDS should be referred to as SDS (PAGE 10) First Paragraph MSDS should be SDS (Page 13) MSDS should be SDS (Page 14) MSDS should be SDS (Page 19) MSDS should be SDS
Status: Update in Progress

Date: 5/13/2021 11:49:04 AM
Module: 360203b
Version: 21
Page: 7
Comment: Under Caution: MSDS should read SDS
Status: Update in Progress

Date: 5/13/2021 11:49:26 AM
Module: 360203cA
Version: 21
Page: 4
Comment: First 2 paragraphs have MSDS, It should read SDS
Status: Update in Progress

Date: 5/13/2021 11:49:39 AM
Module: 360203cA
Version: 21
Page: 13
Comment: third paragraph: Resin to oil should read oil to resin.
Status: Update in Progress

Date: 5/13/2021 11:49:53 AM
Module: 360203cB
Version: 21
Page: 1
Comment: intro reads MSDS, should read SDS
Status: Update in Progress

Date: 5/13/2021 11:50:15 AM
Module: 360203cB
Version: 21
Page: 9
Comment: 4th sentence should read: replace "do" with "if"
Status: Update in Progress

Date: 5/12/2021 4:13:20 PM
Module: 360204a
Version: 21
Page: 5
Comment: Drawing showing dimensions should not share between views
Status: Update in Progress

Date: 5/12/2021 4:13:45 PM
Module: 360204a
Version: 21
Page: 7
Comment: Fig 5. Offset from dimension text to dimension line should be 1.5mm not 1mm
Status: Update in Progress

Date: 5/12/2021 4:14:25 PM
Module: 360204a
Version: 21
Page: 6,7
Comment: Extension lines should be 2mm past dimension line, not 3. Figure 4 pg 7, same thing
Status: Declined

Date: 5/12/2021 4:14:37 PM
Module: 360204a
Version: 21
Page: 16
Comment: Fig. 16 Should be leader line to tambour dimension, Position of Tambour open dimension should move off of object line. Need detail drawing for lower right corner dimensioning.
Status: Update in Progress

Date: 5/13/2021 11:50:50 AM
Module: 360204a
Version: 21
Page: 12
Comment: 5 bullet to read: Do not dimension to hidden lines.
Status: Update in Progress

Date: 5/13/2021 11:51:22 AM
Module: 360204a
Version: 21
Page: 12
Comment: 5th point. Change" invisible" lines to hidden lines. 9th point, each additional dimension line 10mm away from previous one. Not 10-14mm.
Status: Update in Progress

Date: 5/12/2021 4:14:57 PM
Module: 360204bB
Version: 21
Page: 4
Comment: Division numbers are now a 6 digit number, not 5.
Status: Update in Progress

Date: 5/12/2021 4:15:19 PM
Module: 360204bB
Version: 21
Page: 16
Comment: Update national and alberta building code pictures to 2020.
Status: Update in Progress

Date: 5/12/2021 4:15:29 PM
Module: 360204bB
Version: 21
Page: 17-42
Comment: Update all code related images to 2020.
Status: Update in Progress

Date: 5/12/2021 4:16:39 PM
Module: 360204bB
Version: 21
Page: 4
Comment: Division numbers have changed to 6 digits. Please update. (Alberta Building Code)
Status: Update in Progress

Date: 5/12/2021 4:16:52 PM
Module: 360204bB
Version: 21
Page: 18 -25
Comment: Update images to current National building code.
Status: Update in Progress

Date: 5/12/2021 4:17:03 PM
Module: 360204bB
Version: 21
Page: 16, 17, 28-42
Comment: Update all pages to National Building Code.
Status: Update in Progress

Date: 5/12/2021 4:15:40 PM
Module: 360204c
Version: 21
Page: 43,44
Comment: Fig. 46, 47, 49 . Drawings are inaccurate and misleading
Status: Update in Progress

Date: 5/12/2021 4:17:53 PM
Module: 360204e
Version: 21
Page: 39
Comment: Figure 45. Text and dimension should be same size.
Status: Update in Progress

Date: 5/12/2021 4:18:05 PM
Module: 360204e
Version: 21
Page: 45
Comment: Figure 51. Cutting plane line should be triple thick, darker than object lines.
Status: Update in Progress

Date: 5/13/2021 11:51:38 AM
Module: 360204e
Version: 21
Page: 16
Comment: Figure 16. Change "standard" to "common"
Status: Update in Progress

Date: 5/13/2021 2:06:31 PM
Module: 360204e
Version: 21
Page: 12
Comment: Fig 12. Update image to 2020
Status: Update in Progress

Date: 5/13/2021 2:06:57 PM
Module: 360204e
Version: 21
Page: 13
Comment: Fig 13, update image to 2020
Status: Update in Progress


Archived Comments

There are no archived comments to view for this package.