Parts Technician (PAR)

Second Period Package (52 Modules) Comments

Date: 5/31/2019 11:17:03 PM
Module: 270201a
Version: 10
Page: 12
Comment: Arrow on figure 11 pointing to cylinder. Change cylinder to read cylinder liner.
Status: Approved for Review

Date: 11/4/2019 2:10:52 PM
Module: 270201a
Version: 21
Page: 19
Comment: Figure 20. The Clearance Volume for the diesel engine needs to be reduced by 50%. Right now it is shown as the same as the Gas engine.
Status: Approved for Review

Date: 11/4/2019 2:11:07 PM
Module: 270201b
Version: 21
Page: 8
Comment: Figure 10 was replaced. Please add an insert (split) style bearing.
Status: Approved for Review

Date: 11/4/2019 2:11:28 PM
Module: 270201b
Version: 21
Page: 31
Comment: Objective One Exercise Answers 1 a) add (wrist pin) behind piston pin as in figure 1 on page 2.
Status: Approved for Review

Date: 11/4/2019 2:11:43 PM
Module: 270201c
Version: 21
Page: 36
Comment: For question 2. please add two additional line to write out the answer.
Status: Approved for Review

Date: 11/4/2019 2:12:04 PM
Module: 270201c
Version: 21
Page: 41
Comment: Self-test Answers #15 Remove the answer "stronger ring lands" the module does not support or even mention this. Asnwer b) could be split up or change the wording in the question on page 40.
Status: Approved for Review

Date: 11/4/2019 2:12:31 PM
Module: 270201d
Version: 21
Page: 30
Comment: Objective Three Exercise, Question 2 change the word "five" to "four"
Status: Approved for Review

Date: 11/4/2019 3:07:20 PM
Module: 270201d
Version: 21
Page: 37
Comment: Self-Test, question numbering. The number is out of sync. jumps from number 2 to number 6.
Status: Approved for Review

Date: 1/14/2020 3:14:48 PM
Module: 270201d
Version: 21.0
Page: 39
Comment: Due to self test questions missing on page 37, the answers are not in correct order. Also answers for questions 14, 15 and 16 are not shown
Status: Approved for Review

Date: 11/4/2019 3:07:34 PM
Module: 270201e
Version: 21
Page: 15
Comment: Under the heading Types. change the word "three" to "four".
Status: Approved for Review

Date: 11/4/2019 3:07:55 PM
Module: 270201e
Version: 21
Page: 17
Comment: Sentence above figure 24. Replace "solid" with the words "flat faced".
Status: Approved for Review

Date: 11/5/2019 8:14:55 AM
Module: 270201e
Version: 21
Page: 22
Comment: Objective Two Exercise question 2. Change "three (3) to "four (4)"
Status: Approved for Review

Date: 11/5/2019 8:15:16 AM
Module: 270201e
Version: 21
Page: 36
Comment: Objective Two Exercise Answers, question 2, Add "d) hinged roller
Status: Approved for Review

Date: 11/4/2019 2:08:13 PM
Module: 270201f
Version: 21
Page: 7
Comment: Under the heading Ports. first sentence, add the word exhaust between the words "and" and "out" to read "and exhaust out".
Status: Approved for Review

Date: 11/4/2019 2:08:26 PM
Module: 270201f
Version: 21
Page: 5
Comment: Figure 5 was replaced. Find a picture of a various types of cylinder heads. (One cylinder, Two cylinder and Six cylinder - Heavy duty application) or put the original picture back in.
Status: Approved for Review

Date: 11/4/2019 2:08:57 PM
Module: 270201f
Version: 21
Page: 23
Comment: In the NOTE box. add "with a painted stripe" between the words "coded" and "to"
Status: Approved for Review

Date: 11/4/2019 2:09:14 PM
Module: 270201f
Version: 21
Page: 41
Comment: Add a heading to bottom of the page, "Storage" and the sentence. " Cylinder head gasket must be stored flat in their original packaging."
Status: Approved for Review

Date: 11/20/2019 8:15:07 AM
Module: 270201h
Version: 21
Page: 2
Comment: Module is missing the NOTES column.
Status: Approved for Review

Date: 11/20/2019 8:15:20 AM
Module: 270201h
Version: 21
Page: 12
Comment: Remove the section on Viscosity Index and Figure 10.
Status: Approved for Review

Date: 11/20/2019 8:15:37 AM
Module: 270201h
Version: 21
Page: 42
Comment: Add the heading "Filter Storage" after Figure 45. add, Store filters in a clean. coll, dry environment. Filter media breaks down overtime so watch the date code on the filter and rotate the inventory using the first-in, First-out (FIFO) method.
Status: Approved for Review

Date: 11/19/2019 8:28:59 AM
Module: 270201j
Version: 21
Page: 13
Comment: The description above Figure 10. Replace the words "mesh screen" with "bowl" and remove the word "of" Should now read, An example of a bowl type pre-cleaner is shown in Figure 10.
Status: Approved for Review

Date: 11/19/2019 8:29:14 AM
Module: 270201j
Version: 21
Page: 32
Comment: Figure 31, Original picture was replaced with the wrong one. Reinsert original or get a proper replacement.
Status: Approved for Review

Date: 11/19/2019 8:29:29 AM
Module: 270201j
Version: 21
Page: 34
Comment: Sentence above Figure 31, remove the comma between the words "near and peak" to read "near peak torque speed."
Status: Approved for Review

Date: 11/19/2019 8:28:21 AM
Module: 270201k
Version: 21
Page: 31
Comment: Objective Five Exercise, Question 3, Add two additional line to write in the answer.
Status: Approved for Review

Date: 1/8/2020 8:15:26 AM
Module: 270201l
Version: 21
Page: 27
Comment: Objective Two Exercise Question 4, Add the words "of the air" between density -- in. to read: List the two (2) primary inputs that control speed and density of the air in a TBI system?
Status: Approved for Review

Date: 1/8/2020 8:59:49 AM
Module: 270201l
Version: 21
Page: 27
Comment: Objective Two Exercise Question 2 Add the words "fuel pressure" between the words normal --- operating. To read: What is the normal fuel pressure operating pressure of the throttle body injection system?
Status: Approved for Review

Date: 2/19/2020 5:53:52 AM
Module: 270201p
Version: 21
Page: 15
Comment: Figure 23 is missing its graphic
Status: Approved for Review

Date: 2/19/2020 5:54:02 AM
Module: 270201p
Version: 21
Page: 26
Comment: Just above figure 41 the abbreviation PWM is used. This maybe the first occurrence could we say '"Pulse Width Modulated" (PWM)
Status: Approved for Review

Date: 2/19/2020 5:54:12 AM
Module: 270201p
Version: 21
Page: 32
Comment: Under the Heading Diesel Intake and Exhaust Systems and Emission Control Remove "Aside from the changes to accommodate EGR the were explaining earlier"
Status: Approved for Review

Date: 2/19/2020 5:54:22 AM
Module: 270201p
Version: 21
Page: 34
Comment: Objective One Exercise, question 6 Answer (a) is not stated in the module, on page 10 it says used on many newer vehicles.
Status: Approved for Review

Date: 2/19/2020 5:54:32 AM
Module: 270201p
Version: 21
Page: 43
Comment: First paragraph, last sentence, change is to "was" and later to" earlier"
Status: Approved for Review

Date: 2/19/2020 5:54:44 AM
Module: 270201p
Version: 21
Page: 43
Comment: Figure 66, Remove space from the label, EGR/ Charge Air Mixer
Status: Approved for Review

Date: 5/31/2019 11:17:03 PM
Module: 270202f
Version: 4
Page: 32
Comment: Change questions 3 and 4 on page 32 to read CV joint rather than u-joint.
Status: Approved for Review

Date: 11/20/2019 2:50:26 PM
Module: 270202h
Version: 21
Page: 7
Comment: Under Configurations heading. Delete third bullet. There is no explanation on the following pages about this bullet.
Status: Approved for Review

Date: 1/7/2020 12:20:57 PM
Module: 270203a
Version: 21
Page: 39
Comment: Figure 31 has been changed from barrel graphic. Students prefer the previous barrel graphic to the new structural tree graphic.
Status: Approved for Review

Date: 2/21/2020 11:16:04 AM
Module: 270204g
Version: 21
Page: 33
Comment: Under the heading Automotive Paint, remove the history portion paragraphs 2, 3 and 4.
Status: Approved for Review

Date: 2/21/2020 11:20:31 AM
Module: 270204g
Version: 21
Page: 35
Comment: Under the heading Binder, Second sentence, remove nitrocellulose, alkyd
Status: Approved for Review

Date: 2/21/2020 11:20:46 AM
Module: 270204g
Version: 21
Page: 35
Comment: Under the header Solvent, clean you this section, it mentions lacquer and thinner which ni longer used in the auto body industry.
Status: Approved for Review

Date: 2/21/2020 11:21:14 AM
Module: 270204g
Version: 21
Page: 14
Comment: Inside the NOTE box, second sentence, remove the word "will"
Status: Approved for Review

Date: 3/8/2020 7:30:08 AM
Module: 270204h
Version: 21
Page: 28
Comment: Under the heading Seeding Operation, first sentence, remove the second "to"
Status: Approved for Review

Date: 3/8/2020 7:31:09 AM
Module: 270204i
Version: 21
Page: 29
Comment: In the sentence just above Figure 47, add the word "be" between should and replaced.
Status: Approved for Review


Archived Comments

There are no archived comments to view for this package.