Instrumentation and Control Technician (INT)

First Period Package (52 Modules) Comments

Date: 5/31/2019 11:16:52 PM
Module: 310101aA
Version: 3
Page: 9
Comment: Application of OH&S act: the last bullet in terms of exceptions is"farmers and certain agricultural workers". In light of Enhanced Protection for farm and ranch workers act, this needs to be revised. From Jan 1st, 2016: WCB insurance coverage is required for paid workers OH&S basic safety standard applicable for paid workers
Status: Approved for Review

Date: 5/31/2019 11:16:52 PM
Module: 310101aA
Version: 3
Page: 10
Comment: Typo in Item (1) "A worker who is not competent to perform work that may endanger the worker of [to be change to "or"] others must not perform the work except under the direct supervision of a worker who is competent to perform the work."
Status: Approved for Review

Date: 5/31/2019 11:16:53 PM
Module: 310103a
Version: 1
Page: 2
Comment: The word "system" needs to be deleted in at least three places because it is redundant producing poor grammar. The names SI and USCS already include "system" in the name and repeating "system" after them is poor grammar. Table 1 - Common SI system units. Should read - Common SI units. The sentence "...used in the USCS system and.... should read used in the USCS and.... Table 2 - Common USCS system units. Should read - Common USCS units.
Status: Approved for Review

Date: 5/31/2019 11:16:53 PM
Module: 310103a
Version: 1
Page: 31
Comment: Grammar in the first bullet phrase "is also very accurate" should read "the area between the nozzle and ball is also very precise."
Status: Approved for Review

Date: 5/31/2019 11:16:53 PM
Module: 310103a
Version: 1
Page: 33
Comment: Third bullet should be deleted or moved to bottom of page 34 as it refers to the Well Manometer seen there and not the U-Tube Manometers. It says "The scale on this manometer is marked so that only one reading is required rather than two readings(the top and bottom)."
Status: Approved for Review

Date: 5/31/2019 11:16:53 PM
Module: 310103a
Version: 1
Page: 18
Comment: The word gravity needs to be deleted from the top paragraph so the sentence matches the equation following it.
Status: Approved for Review

Date: 5/31/2019 11:16:53 PM
Module: 310103a
Version: 1
Page: 24
Comment: The last sentence says "By convention, particular values for gravity and density/temperature are implied." Those implied values should be listed here after this statement.
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 26
Comment: The word "primary" should be removed from the description of working standards so the students don't claim the module calls primary standards working standards. It could read "Working standards for pressure measurement are of "utmost" importance in the measurement industry"
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 37
Comment: The paragraph at the bottom should match the typical well manometer students will see in the lab.
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 38
Comment: 6th bullet needs to change psi to kPa. It says a typical master gauge is 20,000 psi.This is not true. I think it should be 20,000 kPa which matches the 3,000 psi Master gauge in the pictures Fig 26 & Fig 27
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 39
Comment: 3rd bullet needs to change psi to kPa. It says a typical master gauge is 20,000 psi. This is not true. I think it should be 20,000 kPa which matches the 3,000 psi Master gauge in the pictures Fig 26 & Fig 27
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 41
Comment: Centre of page "s" needs to be added to "your solution(s) would look as follows." as there is more than one solution listed. poor grammar.
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 44
Comment: Printing error is symbol of "minus" comes out as a square.
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 45
Comment: Printing error is symbol of "minus" comes out as a square.
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 3
Comment: Missing a zero in the example calculation. should read "50mm means 50 x (0.001) - 0.05 metres"
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 8
Comment: s needs to be added to the phrase "water seek(s) its own level" - Poor grammar
Status: Approved for Review

Date: 5/31/2019 11:16:54 PM
Module: 310103a
Version: 1
Page: 23
Comment: The note box misspells metre(length) with meter(gauge)
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 5
Comment: ro does not print properly in the phrase "and is pronounced ro" I would suggest using the phonetic spelling of rho so the phrase reads: "and is pronounced row as in row your boat"
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 19
Comment: The number 9.81169 for gravity should be replaced with 9.80665 given on page 32 as students mistake it for the standard and try to use it in their calculations.
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 43
Comment: The first paragraph says that pressure can be expressed as 1. Absolute, 2. Gauge 3. Atmospheric, 4. Vacuum. I am not sure it can be expressed as Atmospheric. I think you should delete it or add Differential Pressure.
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 48
Comment: Self test #4 book has wrong answer. 551.665 kPa
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 31
Comment: Grammar second bullet. "very accurate" should read "very precise"
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 34
Comment: Add this sentence to the bottom of this page. "The scale on this well manometer is marked so that only one reading is required rather than two readings(top and bottom)"
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 35
Comment: The 4th bullet implies that the manometers in our labs are reading incorrectly, and need a correction factor, because the scale is made for zero degrees C and our lab is at 20 degrees. Please reword this bullet.
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 37
Comment: The 4th bullet implies that the manometers in our labs are reading incorrectly, and need a correction factor, because the scale is made for zero degrees C and our lab is at 20 degrees. Please reword this bullet.
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 36
Comment: Fig 25 is a variation of the inclined well manometer. I think it would be better if the basic well manometer is shown here to the students first so they can learn how it works before looking at the variation.
Status: Approved for Review

Date: 5/31/2019 11:16:55 PM
Module: 310103a
Version: 1
Page: 37
Comment: Paragraph at bottom should be moved to bottom of page 36 close to the fig 25 it is referring to.
Status: Approved for Review

Date: 5/31/2019 11:16:56 PM
Module: 310103a
Version: 1
Page: 16
Comment: Top paragraph and equation on page 16 belongs to, and should be moved to, the previous page to improve clarity of the next example.
Status: Approved for Review

Date: 5/31/2019 11:16:56 PM
Module: 310103a
Version: 1
Page: 19
Comment: The example at the bottom of the page gives two heights for the fluid level 3m and 2.545m. "3 m high" should be deleted to match the calculations below.
Status: Approved for Review

Date: 5/31/2019 11:16:56 PM
Module: 310103a
Version: 1
Page: 20
Comment: The sentence "if you are working in feet (lbf)" Should read "if you are working in feet (psf)" because the examples calculate the pressure into pounds per square foot (psf) and then pounds per square inch(psi).
Status: Approved for Review

Date: 5/31/2019 11:16:59 PM
Module: 310103fA
Version: 3.2
Page: 34
Comment: I believe there should be a tool added to the ILM. The Multitool, such as the FEIN multimaster is an invaluable tool for the tradesperson, especially people in the installation of millwork and flooring. www.fein.com
Status: Approved for Review

Date: 5/31/2019 11:16:50 PM
Module: 310105g
Version: 3
Page: 20
Comment: Example on page 20 there is a typo. In the question it gives a height of 2.45 cm. In the solution the height is written 2.54cm
Status: Approved for Review

Date: 5/31/2019 11:16:50 PM
Module: 310105g
Version: 3
Page: 17
Comment: Example on page 17 there is a typo. In the question it gives a diameter of 8.25cm. In the solution the diameter is written 8.28cm.
Status: Approved for Review

Date: 5/31/2019 11:16:50 PM
Module: 310105g
Version: 3
Page: 20
Comment: Example on page 20 there is a typo. In the question it gives a height of 2.45 cm. In the solution the height is written 2.54cm
Status: Approved for Review

Date: 5/31/2019 11:16:50 PM
Module: 310105g
Version: 3
Page: 17
Comment: Example on page 17 there is a typo. In the question it gives a diameter of 8.25cm. In the solution the diameter is written 8.28cm.
Status: Approved for Review

Date: 5/31/2019 11:16:50 PM
Module: 310105g
Version: 3
Page: 45
Comment: Question number 13: Gives the wrong coefficient for the expansion of steel for the answer in the back of the book. It gives 13.0x10^-6/°c it is suppose to be 1.3x10^-5/°c to get the correct answer. I compared the question with an older version and the older version has the correct coefficient.
Status: Approved for Review


Archived Comments

There are no archived comments to view for this package.